7.5KW 220V 380V ATC Air Cooled Spindle Motor BT30 Automatic Tool Changer 800hz

$1590.0 Buy It Now or Best Offer
free,30-Day Returns

Seller Store powace08
() %,

Location: Changzhou
Ships to: US,
Item: 275083779737

Restocking Fee:No
Return shipping will be paid by:Buyer
All returns accepted:Returns Accepted
Item must be returned within:30 Days
Refund will be given as:Money back or replacement (buyer’s choice)
Country/Region of Manufacture:China
MPN:Does Not Apply
Electric current:13.5A
Rated power:7.5KW
Pole:4 Pole
Peak torque:7.5Nm
Rated torque:6Nm
RATTM MOTOR:RATTM MOTOR

7.5KW 220V 380V ATC Air Cooled Spindle Motor BT30 Automatic Tool Changer 800hz 24000rpm Package include:1 x 7.5KW BT30 ATC Automatic tool changer Air cooled spindle motor 220V or 380V 1 x BT30-ER25 Tool Holder with pull stud 2 x Air plug English user manual 100% Brand New and High Quality!!!Spindle modelRTM120X103-30-24/7.5Voltage220V or 380VElectric current13.5ARated speed12000rpmRated frequency800HzRated power7.5KWPeak power9KWRated torque6NmPeak torque7.2NmMotor Pole4 PoleMaximum speed24000rpm 1.This spindle is built-in type spindle motor, built-in three asynchronous motors,by the inverter control.As the spindle has a compact structure,high power, big torque, small vibration, low noise characteristics,so it can achieve high speed,high powe cutting,high recision and high stability operation.2.The bearing of spindle use grease lubricated angular to contact bearings,can be achieved lifelong lubricating within the life cycle. 3.This spindle uses air cooling to cool the motor and front and rear bearings. The wind is provided by the fan at the rear end, from the rear of the spindle through the inner and outer air slots directly to the front of the spindle, there by taking away the heat generated by the high-speed rotation of the spindle, achieving thermal balance, and keeping the temperature of the electric spindle within a certain value. 4.The spindle built-in PTC 140 temperature sensor(Technical parameters are visible in other sections of this specification),you can read it anytime if you need to protect the motor temperature. 5. The tool clamping methods:this spindle built-in automatic tool changedevice,shank form is BT30. Please note that when stopping the spindle, you need to wait until the spindle is stopped before using the tool, so as to avoid causing the spindle and the tool mechanism to be connected together and cannot be separated. When loosening the tool and broaching the tool, you need to return the air, and pls keep the air intake and return air during the whole work. Spindle installation explanation 1.Fan cooling system description When the spindle rotates, the rear fan system must be started to ensure the correct supply voltage and the supply voltage is 12V. 2.Air sealing control (AS) In order to prevent water or impurities enters internal of the spindle,spindle will have gas sealing device,the gas seal machine must be started start with the machine at the same time. And the need to go through multi-stage filtration. 3.Compressed gas quality requirements The quality requirement of gas which is used in gas seals:Oil content：﹤0.01mg/m³solid particle：﹤5µ mPressure dew point：﹤7.5℃（0.7MPa） 3. Running-in program instructions Only all monitoring issued no failures operational signals,at the same time,all safety devices have been installed and working properly,then allow start spindle. Note: new or spindle which is not used for a long time must to be running slowly.First,start run spindle for half an hour as 25% of the maximum speed,then increase to 50% of the maximum speed,to run 15 minutes,finally,increase to maximum speed.It’s need to check the temperature of the spindle during the whole process, spindle will get hot, but not hot hand, if the spindle becomes hot, pls stop the operation and contact our customer service department. [link removed by eBay]No.projectStandard1Spindle blowing dust/seal gas pressure(MPa)0.2-0.252Spindle gas seal gas flow（L/min)65±10(When on Working）3Cooling air fan pressure（MPa)≧0.254Cooling air fan flow（L/min)≧2.55Spindle static state pulse（µm）≦36Spindle vibration（mm/s）≦1.08Spindle assembly methodBottom mounting（6-M8）9Motor windings Pressure test（V/M）1000V//1 minute withstanding Voltage test10Tool InterfaceBT3011Inverter Specifications7.5KW（220V)12FitmentWoodworking machinery, polishing industry, etc.No.FunctionDefinition1Gas sealing（Protection of impurities into the spindle 0.2-0.25MPa）Ф62Return air（piston reset 0.35-0.45MPa）Ф65Power supply（Spindle power lines with thermistor）U/V/W/ Ground wire6Intake air（Spindle tool open 0.5-0.6MPa）Ф67sensor（spindle tool change signals 24V）Tool close/open8fan（spindle cooling）12V Our products are equipped with a single thermistor PTC140, it can be used for spindle temperature protection. 7. Product Tool Change Signals DescriptionSensor Model (0-24V, PNP), The spindle built two sensors.wiring Diagram is as follows:1. Response broach knife signal, when the knife handle is hang, black sensor output signal;2. Response loose knife signal, when the knife jaws open,black sensor output signal; Shipping Please open the package and check if there are some damages before sign, if there are some damages , please do not sign and contact us immediately Items will be shipped within 1-2 days upon the receipt of payment. Payment We accept paypal payment, all Paypal must be confirmed(shipping and billing address must match and correct and it need tell us your telephone no for delivery) Problem&Feedback Please give us the opportunity to resolve any problem when you have, we concern your problem and we will try our best to resolve it. We are a new member in ebay now, and need understand both of sides Pls email us before you want to leave any negative feedback Refund When you have the parcel, and not satisfied the goods or it is other problem like as broken,pls tell us the detail reason and provide the photos Any reason required for all refund. Item must be in it’s original condition and no physical damage. Buyer responsible for all shipping cost Contact us Welcome worldwide customer inquire and questions, we will try to do our best to feedback customer’s email within 1-2 business days,if not pls check the mail box again Customer’s satisfaction is very important to us.

Frequently Asked Questions About 7.5KW 220V 380V ATC Air Cooled Spindle Motor BT30 Automatic Tool Changer 800hz in My Website

solucionesencloud.com is the best online shopping platform where you can buy 7.5KW 220V 380V ATC Air Cooled Spindle Motor BT30 Automatic Tool Changer 800hz from renowned brand(s). solucionesencloud.com delivers the most unique and largest selection of products from across the world especially from the US, UK and India at best prices and the fastest delivery time.

What are the best-selling 7.5KW 220V 380V ATC Air Cooled Spindle Motor BT30 Automatic Tool Changer 800hz on solucionesencloud.com?

Frequently Asked Questions About 7.5KW 220V 380V ATC Air Cooled Spindle Motor BT30 Automatic Tool Changer 800hz in My Website

What are the best-selling 7.5KW 220V 380V ATC Air Cooled Spindle Motor BT30 Automatic Tool Changer 800hz on solucionesencloud.com?

Add a comment Cancelar la respuesta

Soluciones en Cloud

台灣找工作平台